Coatings An Industrial coatings is a paint or coating defined by its protective, rather than its aesthetic properties, although it can provide both.The most common use of Industrial coatings is for corrosion control of steel or concrete. Other functions include intumescent coatings for fire resistance. The most common polymers used in Industrial coatings are polyurethane, Epoxy Coatings and moisture cure urethane.

Ultimate Linings is a fast setting, rapid curing, aromatic, two components, hybrid polyurea/polyurethane spray designed to be applied over EPS, wood and many other surfaces. Its excellent balance of stiffness and impact resistance provides excellent plastic “shell-like” protection for delicate foams and EPS. Its chemical design allows fast “user-friendly” application with excellent flow and appearance.

SURFACE PREPARATION In general, coatings performance and adhesion are directly proportional to surface preparation. Most failures in the performance of surface coatings can be attributed to poor surface preparation. Polyurea coatings ,Protective Coatings rely on the structural strength of the substrate to which they are applied. All surfaces must be free of dust, dirt, oil, grease, rust, corrosion and other contaminants. When coating substrates previously used, it is important to consider the possibility of substrate absorption, which may affect the adhesion of the coating system, regardless of the surface preparation. It recognizes the potential for unique substrates from one project to another.

FEATURES TYPICAL

*Plastic “Shell-Like” Protection *Low Shrinkage *100% Solids *Zero VOC *Meets USDA Criteria / Fast Cure *Excellent Thermal Stability / High Productivity *Excellent Chemical Protection *Excellent Cold Temperature Impact Resistance

USES

Decorations / Props, Speaker Boxes Architectural Shapes, Dock Flotation’s, Steel Coating, Wood Pallets / Crates Food Processing Plants, Wood Cabinets Industrial product formulations offer solutions for abrasion resistance, water proof coatings, blast resistance, hazardous materials containment energy, ballistic armor, chemical resistance, energy efficient insulation, structural reinforcement, corrosion resistance, fire retardant and thermal barrier coatings.

Aluminum: Aluminum should be blasted with aluminum oxide or sand, and not with steel or metal grit. Excessive blasting may result in a warped or deformed surface. After blasting, wash aluminum with a commercially available aluminum cleaner. Allow to dry, then prime.

Brass and Copper:Brass and copper should be blasted with sand, and not with steel or metal grit. Remove all dust and grease prior to applying primer.

Galvanized Surfaces: Clean and degrease any contaminated surfaces before priming. Do not blast galvanized surfaces with an abrasive grit. An adhesion test is recommended prior to starting the project. Fiberglass Reinforced Plastic: The gel coat should be lightly blasted or sanded with 80 grit sandpaper and cleaned.

Plastic Foams:
Enhanced adhesion is obtained when the foam is mechanically abraded. When coating polystyrene, do not use a solvent-based primer.
Textiles, Canvas, Fabrics:
Adhesion to most fabrics, geothermal membranes and textiles does not require a primer.
Stainless Steel:
Stainless steel may be grit blasted and degreased before priming. Some stainless steel alloys are so inert that it is not possible to achieve a satisfactory bond. An adhesion test is recommended prior to starting the project.

Views: 16

Tags: Automotive, Chemical, Coatings, Epoxy, Floor, Flooring, Home, Improvement, Industrial, Polyurethane, More…Protective, Roof, Roofing, Waterproof, coatings

Comment

You need to be a member of www.IndustryBuzzZ.com MEDIA to add comments!

Join www.IndustryBuzzZ.com MEDIA

SUPPORT A POSTITIVE MESSAGE

 

FOR RADIO COMMERCIALS, MAGAZINE PLACEMENT, TELEVISION ADS AND MORE

ADVERTISE WITH US TODAY CALL (678) 792-8999 OR EMAIL CONNECT@INDUSTRYBUZZZ.COM

 

Check Out Entertainment Podcasts at Blog Talk Radio with IndustryBuzzZ Media on BlogTalkRadio

Connect With Us

Latest Activity

www.IndustryBuzzz.com via Facebook
Thumbnail

I am inspired to #BEEcome more and this Nun does too she is all into it #PraiseTheLord what do you think about the song she selected?

Miren el talento especial que tiene esta monja.

2:06

Facebook21 hours ago · Reply
www.IndustryBuzzz.com via Facebook
Thumbnail

I am inspired to #BEEcome we can train our youth to #BEEcome more all it takes is us to take the time and train them

Youngest Call Center Agent

Is it just me or are…

See More
Facebook22 hours ago · Reply
www.IndustryBuzzz.com via Facebook
Thumbnail

#GETCANDID with @LUTONYAMRUSSELL & @NikkiWashington on @IndustryBuzzZ radio tune in at www.IndustryBuzzZ.com Media Network... Join other celebrities and SET UP YOUR PROFILE TODAY!!! Become a PROUD sponsor today (678) 792-8999 or email us…

See More
FacebookTuesday · Reply
www.IndustryBuzzz.com via Facebook
Thumbnail

I am inspired to #BEECOME a salsa dancer because they #BEEcame congrats to the dancers

Some pretty amazing Salsa dancing

Can any of YOU dance Salsa like…

See More
FacebookMonday · Reply

Badge

Loading…

© 2014   Created by IndustryBuzzZ.com Media.

Badges  |  Report an Issue  |  Terms of Service

Offline

Live Video

Related Posts Plugin for WordPress, Blogger...