Coatings An Industrial coatings is a paint or coating defined by its protective, rather than its aesthetic properties, although it can provide both.The most common use of Industrial coatings is for corrosion control of steel or concrete. Other functions include intumescent coatings for fire resistance. The most common polymers used in Industrial coatings are polyurethane, Epoxy Coatings and moisture cure urethane.

Ultimate Linings is a fast setting, rapid curing, aromatic, two components, hybrid polyurea/polyurethane spray designed to be applied over EPS, wood and many other surfaces. Its excellent balance of stiffness and impact resistance provides excellent plastic “shell-like” protection for delicate foams and EPS. Its chemical design allows fast “user-friendly” application with excellent flow and appearance.

SURFACE PREPARATION In general, coatings performance and adhesion are directly proportional to surface preparation. Most failures in the performance of surface coatings can be attributed to poor surface preparation. Polyurea coatings ,Protective Coatings rely on the structural strength of the substrate to which they are applied. All surfaces must be free of dust, dirt, oil, grease, rust, corrosion and other contaminants. When coating substrates previously used, it is important to consider the possibility of substrate absorption, which may affect the adhesion of the coating system, regardless of the surface preparation. It recognizes the potential for unique substrates from one project to another.

FEATURES TYPICAL

*Plastic “Shell-Like” Protection *Low Shrinkage *100% Solids *Zero VOC *Meets USDA Criteria / Fast Cure *Excellent Thermal Stability / High Productivity *Excellent Chemical Protection *Excellent Cold Temperature Impact Resistance

USES

Decorations / Props, Speaker Boxes Architectural Shapes, Dock Flotation’s, Steel Coating, Wood Pallets / Crates Food Processing Plants, Wood Cabinets Industrial product formulations offer solutions for abrasion resistance, water proof coatings, blast resistance, hazardous materials containment energy, ballistic armor, chemical resistance, energy efficient insulation, structural reinforcement, corrosion resistance, fire retardant and thermal barrier coatings.

Aluminum: Aluminum should be blasted with aluminum oxide or sand, and not with steel or metal grit. Excessive blasting may result in a warped or deformed surface. After blasting, wash aluminum with a commercially available aluminum cleaner. Allow to dry, then prime.

Brass and Copper:Brass and copper should be blasted with sand, and not with steel or metal grit. Remove all dust and grease prior to applying primer.

Galvanized Surfaces: Clean and degrease any contaminated surfaces before priming. Do not blast galvanized surfaces with an abrasive grit. An adhesion test is recommended prior to starting the project. Fiberglass Reinforced Plastic: The gel coat should be lightly blasted or sanded with 80 grit sandpaper and cleaned.

Plastic Foams:
Enhanced adhesion is obtained when the foam is mechanically abraded. When coating polystyrene, do not use a solvent-based primer.
Textiles, Canvas, Fabrics:
Adhesion to most fabrics, geothermal membranes and textiles does not require a primer.
Stainless Steel:
Stainless steel may be grit blasted and degreased before priming. Some stainless steel alloys are so inert that it is not possible to achieve a satisfactory bond. An adhesion test is recommended prior to starting the project.

Views: 16

Tags: Automotive, Chemical, Coatings, Epoxy, Floor, Flooring, Home, Improvement, Industrial, Polyurethane, More…Protective, Roof, Roofing, Waterproof, coatings

Comment

You need to be a member of www.IndustryBuzzZ.com MEDIA to add comments!

Join www.IndustryBuzzZ.com MEDIA

SUPPORT A POSTITIVE MESSAGE

 

FOR RADIO COMMERCIALS, MAGAZINE PLACEMENT, TELEVISION ADS AND MORE

ADVERTISE WITH US TODAY CALL (678) 792-8999 OR EMAIL CONNECT@INDUSTRYBUZZZ.COM

 

Check Out Entertainment Podcasts at Blog Talk Radio with IndustryBuzzZ Media on BlogTalkRadio

Connect With Us

Latest Activity

www.IndustryBuzzz.com via Facebook
Thumbnail

I AM INSPIRED TO #BEEcome.... MORE!!!! GREAT time at the Rhema Word of Life Church & Ministries Center Annual Youth Jamboree hosted by our very own Lutonya M Russell music "Out The Box" by: ZEKE

0:52

Facebook5 hours ago · Reply
www.IndustryBuzzz.com via Facebook
Thumbnail

Check out Rhema Word of Life Church & Ministries Center Annual Youth Jamboree hosted by our #BuzzZinDiva @LutonyaMRussell ... headed by @lumiah_1 awesome event #InspireOurYouth music by: @zekemusik1 Next one Coming Dec. 6th

0:15

Facebook5 hours ago · Reply
www.IndustryBuzzz.com via Facebook
Thumbnail

RIGHT NOW LIVE #GETCANDID with @LUTONYAMRUSSELL & @NikkWashington on @IndustryBuzzZ radio tune in at www.IndustryBuzzZ.com Media Network... Thursday's 5:30PM/CST ... Become a PROUD sponsor today (678) 792-8999 or email us today at…

See More
Facebook8 hours ago · Reply
www.IndustryBuzzz.com via Facebook
Thumbnail

5th Annual Black & White Extravaganza and BuzzZinOFF AWARDS Interviews by Nikki Washington Part 2 : Honoree Pastor Corey Brooks- Project Hood, Honoree Tamika Price, Jon Johnson & Untainted Worship, Youth Hostess Zoie Horton, Youth…

See More
Facebookyesterday · Reply

Badge

Loading…

© 2014   Created by IndustryBuzzZ.com Media.

Badges  |  Report an Issue  |  Terms of Service

Offline

Live Video

Related Posts Plugin for WordPress, Blogger...